Steve Vai demonstrates his "new for 2012" Legacy 3 amp. This amp combines features from the Original Legacy 2-channel amp and features from the Legacy 2. • All-Tube, 3 Channel 100w Amp • Rackmountable - lightest 100w in the industry • Master Volume & foot switchable Boost • Ch 1 Clean Channel - same circuit from original Legacy • Ch 2 Drive Channel - same circuit from original Legacy • Ch 3 Drive Channel with high-gain switch • Ch assignable Reverb • 2 Effect Loops: 1 pre master & 1 post master • MIDI In/Thru • Red/Amber/Green backlit LEDs color changes with channel • Output: 100/50/15 watts • 12AX7 preamp tubes • 4 matched EL34 power tubes • Optional Vai green chassis • 17"wx 9"dx 8.5"h • 29 Lbs • Made in USA This video was shot in Steve's studio. Legacy 3 audio was recorded by Steve's studio equipment. Here is an overview of how the amp is set-up and recorded. Legacy 3 head (primary) - Steve's guitar goes into a few pedals (Wah etc. on the floor) then straight into the front of the primary Legacy 3 amp. Steve uses the Axe-Fx for his delays etc.. The Master Out on the rear of the primary Legacy is connected to the input on the Axe-Fx. The Axe-Fx output is stereo. Left output goes back into the primary Legacy 3 head via the Power Amp In jack. The Right Axe-Fx output goes into the Effect Loop return of a Second Legacy head (bypassing the preamp). Both Legacy heads have a Legacy 2x12 ext. cab connected for a stereo image. The cabs are mic'd up individually (actually 3 ...
Thursday, 13 December 2012
Legacy 3, Steve Vai amp demo - Carvin
Legacy 3, Steve Vai amp demo - Carvin Tube. Duration : 6.38 Mins.
Steve Vai demonstrates his "new for 2012" Legacy 3 amp. This amp combines features from the Original Legacy 2-channel amp and features from the Legacy 2. • All-Tube, 3 Channel 100w Amp • Rackmountable - lightest 100w in the industry • Master Volume & foot switchable Boost • Ch 1 Clean Channel - same circuit from original Legacy • Ch 2 Drive Channel - same circuit from original Legacy • Ch 3 Drive Channel with high-gain switch • Ch assignable Reverb • 2 Effect Loops: 1 pre master & 1 post master • MIDI In/Thru • Red/Amber/Green backlit LEDs color changes with channel • Output: 100/50/15 watts • 12AX7 preamp tubes • 4 matched EL34 power tubes • Optional Vai green chassis • 17"wx 9"dx 8.5"h • 29 Lbs • Made in USA This video was shot in Steve's studio. Legacy 3 audio was recorded by Steve's studio equipment. Here is an overview of how the amp is set-up and recorded. Legacy 3 head (primary) - Steve's guitar goes into a few pedals (Wah etc. on the floor) then straight into the front of the primary Legacy 3 amp. Steve uses the Axe-Fx for his delays etc.. The Master Out on the rear of the primary Legacy is connected to the input on the Axe-Fx. The Axe-Fx output is stereo. Left output goes back into the primary Legacy 3 head via the Power Amp In jack. The Right Axe-Fx output goes into the Effect Loop return of a Second Legacy head (bypassing the preamp). Both Legacy heads have a Legacy 2x12 ext. cab connected for a stereo image. The cabs are mic'd up individually (actually 3 ...
Steve Vai demonstrates his "new for 2012" Legacy 3 amp. This amp combines features from the Original Legacy 2-channel amp and features from the Legacy 2. • All-Tube, 3 Channel 100w Amp • Rackmountable - lightest 100w in the industry • Master Volume & foot switchable Boost • Ch 1 Clean Channel - same circuit from original Legacy • Ch 2 Drive Channel - same circuit from original Legacy • Ch 3 Drive Channel with high-gain switch • Ch assignable Reverb • 2 Effect Loops: 1 pre master & 1 post master • MIDI In/Thru • Red/Amber/Green backlit LEDs color changes with channel • Output: 100/50/15 watts • 12AX7 preamp tubes • 4 matched EL34 power tubes • Optional Vai green chassis • 17"wx 9"dx 8.5"h • 29 Lbs • Made in USA This video was shot in Steve's studio. Legacy 3 audio was recorded by Steve's studio equipment. Here is an overview of how the amp is set-up and recorded. Legacy 3 head (primary) - Steve's guitar goes into a few pedals (Wah etc. on the floor) then straight into the front of the primary Legacy 3 amp. Steve uses the Axe-Fx for his delays etc.. The Master Out on the rear of the primary Legacy is connected to the input on the Axe-Fx. The Axe-Fx output is stereo. Left output goes back into the primary Legacy 3 head via the Power Amp In jack. The Right Axe-Fx output goes into the Effect Loop return of a Second Legacy head (bypassing the preamp). Both Legacy heads have a Legacy 2x12 ext. cab connected for a stereo image. The cabs are mic'd up individually (actually 3 ...
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment